Our Archives

Call 09159097300, or 09067754232 for any enquiries.

Project Topic:

DESIGN OF A FULL ADDER CIRCUIT

Project Information:

 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 35 ::   Attributes: EXPERIMENT ::   5,131 people found this useful
Get the complete project »

Project Body:

CHAPTER TWO

 

 

 

2.0           LITERATURE REVIEW

 

 

 

According to the novel by Mehdi Ghasemi, Mohammad Hussein Moaiyeri, Keivan Navi, published on Jan 10, 2012. Due to high power consumption and difficulties with minimizing the CMOS transistor size, molecular electronics has been introduced as an emerging technology. Further, there have been noticeable advances in fabrication of molecular wires and switches and also molecular diodes can be used for designing different logic circuits.

 

Considering their technology novel, they use molecules as the active components of the circuit, for transporting electric charge. They presented a full adder circuit based on molecular electronics. This full adder is consisted of resonant tunneling diodes and transistors which are implemented via molecular electronics. The area occupied by this kind of full adder would be much times smaller than the conventional designs and it can be used as the building block of more complex molecular arithmetic circuits.

 

Ramya Menon C. and Vinod Pangracious 16 Jan 2012 published a novel which declares that; in a multiprocessor system on chip (MPSOC) IC the processor is one of the highest heat dissipating devices. The temperature generated in an IC may vary with floor plan of the chip. The novel proposes an integration and thermal analysis methodology to extract the peak temperature and temperature distribution of 2-dimensional and 3-dimensional multiprocessor system-on-chip. As we know the peak temperature of chip increases in 3-dimensional structures compared to 2-dimensional ones due to the reduced space in intra-layer and inter-layer components.

 

In sub-nanometer scale technologies, it is inevitable to analyze the heat developed in individual chip to extract the temperature distribution of the entire chip. With the technology scaling in new generation ICs more and more components are integrated to a smaller area. Along with the other parameters threshold voltage is also scaled down which results in exponential increase in leakage current. This has resulted in rise in hotspot temperature value due to increase in leakage power. They analyzed the temperature developed in an IC with four identical processors at 2.4 GHz in different floor plans. The analysis has been done for both 2D and 3D arrangements. In the 3D arrangement, a three layered structure has been considered with two Silicon layers and a thermal interface material (TIM) in between them. Based on experimental results they propose a methodology to reduce the peak temperature developed in 2D and 3D integrated circuits.

 

2.1    HISTORY

 

                Until the late 1970’s, most minicomputer did not have a multiple instruction, and so programmers used a “multiply routine” which repeatedly shifts and accumulates partial results, often written using loop unwinding. Mainframe computers had multiply instructions. The Motorola 6809, introduced in 1978, was one of the earliest microprocessors with a dedicated hardware multiplying instruction. It did the same sorts of shifts and adds as a “multiply routine”, but implemented in the microcode of the MUL instruction [citation needed].

 

As more transistors per chip became available due to Larger Scale Integration (LSI), it become possible to put enough adders on a single chip to sum all the partial products at once, rather than reuse a single adder to handle each partial product one at a time. Because common digital signal processing algorithms spend most of their time on multiplying, digital signal processor designers sacrifice a lot of chip area in order to make the multiply-accumulate unit often used up most of the chip area of early DSPs.CHAPTER THREE

 

3.0            RESEARCH METHODOLOGY

 

3.1           SIMILAR WORKS BASED ON FULL ADDER CIRCUITS

 

Some designs of adder cells can be found in the figures 1 to 6. These six different adder cells are simulated in 0.18 µm CMOS technology and tested separately. All these cells are optimum in power dissipation and Power delay product (PDP). The conventional adder shown in figure 1 is implemented with 28 Transistors in CMOS technology. Conventional adder circuits do not function well below one volt supply. Figure 2 shows the Complementary Pass-transistor Logic (CPL) adder. Among the pass transistor logic styles, CPL has the best performance and the lowest power delay product.

 

The Transmission Function full Adder (TFA), which is shown in figure 3, uses 16 transistors. Pull-up and pull-down logic is used to drive the load the same as the complementary pass logic. Figure 4 shows the Transmission Gate full adder (TG). TG adder includes 20 transistors, and generates a+b and its complement to produce the sum and carry signals. It uses complementary input signals (a, b, c) as the complementary CMOS full adder. This full adder uses only 14 transistors to make the adder function. The circuit occupies less area in comparison with other CMOS full adder cells. At end, another full adder with 26 transistors is presented in figure 6.

 

Figure 1: Conventional CMOS full adder


Get The Complete Project »

Project Department:

MORE ELECTRICAL ELECTRONICS ENGINEERING FREE UNDERGRADUATE PROJECT TOPICS AND RESEARCH MATERIALS

Instantly Share this Project On Social Media:

CLOSELY RELATED ELECTRICAL ELECTRONICS ENGINEERING FREE UNDERGRADUATE PROJECT TOPICS AND RESEARCH MATERIALS

SOLAR POWER INVERTERS, ANALYSIS AND TEST EVALUATION
 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 100 ::   Attributes: EXPERIMENT  ::   16498 engagements

INTRODUCTION The quest to satisfy our need for stable power supply in Nigeria has driven most Nigerians into an ardent search for alternative renewable power sources. One of such major renewable power...Continue reading »

DESIGN AND CONSTRUCTION OF MICROCONTROLLER TIMER SOCKET OUTLET

 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 71 ::   Attributes: EXPERIMENT  ::   4981 engagements

CHAPTER ONE INTRODUCTION BACKGROUND INFORMATION As the world becomes concerned with conserving electric power and the fuels that generate electricity, there is a growing need for the conscientio...Continue reading »

DESIGN AND CONSTRUCTION OF A SOLAR POWERED MULTIPLE CELL PHONES CHARGING BOOTH
 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 56 ::   Attributes: EXPERIMENT  ::   6165 engagements

ABSTRACT Cell phones need electric sources to charge their batteries in order to work, but there are people in developing and third world countries that find it hard to access electric sources.In an ...Continue reading »

IMPROVING THE CAPACITY OF A RENEWABLE POWER SYSTEM, USING SOLAR POWER PANEL (A CASE STUDY OF COMPUTER SCIENCE ND SOFTTWARE LAB)
 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 70 ::   Attributes: EXPERIMENT  ::   4404 engagements

CHAPTER ONE INTRODUCTION 1.1 BACKGROUND TO THE STUDY The use of renewable energy increased greatly just after the first big oil crisis in the late seventies. At that time, economic issues were the...Continue reading »

INVESTIGATION OF THE PERFORMANCE INDEX OF 3.5KVA/48V POWER INVERTER
 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 75 ::   Attributes: EXPERIMENT  ::   8444 engagements

ABSTRACT The initial cost of the power inverter system is significant higher compared to the conventional source of power. As a result, there is need for the performance evaluation of various power i...Continue reading »

DESIGN OF INDUSTRIAL BATCH COUNTER
 Format: MS WORD ::   Chapters: 1-5 ::   Pages: 30 ::   Attributes: EXPERIMENT  ::   5298 engagements

CHAPTER ONE INTRODUCTION The industrial batch counter is an electronic and electrical device that handles the counting and controls the flow of individuals using an automated slide door that ...Continue reading »

What are you looking for today?

TESTIMONIALS:

  • 1. Jayone from FPA said " I had a wonderful experience using UniProjectMaterials,though they did not deliver the material on time, but the content had good quality. I recommend UniProjectMaterials for any project research work.".
    Rating: Very Good
  • 2. Mugisha R from B.U, UGANDA said "Wow, this is great, your materials has helped me alot. Many blessings. I will inform my friends. Thanks. ".
    Rating: Very Good
  • 3. Nwachukwu Ruth Chinyerr from Michael okpara university of Agriculture,umudike said "I really appreciate this. Materials like this are good guides to writing a researchable project.".
    Rating: Good
  • 4. Ibrahim Salama from Kaduna said "Thanks You So Much Sir We Appreciate ".
    Rating: Excellent
  • 5. Ibrahim Salama from Kaduna said "Thanks You So Much Sir We Appreciate ".
    Rating: Excellent
  • 6. Mohammed A.B from Veterinary Laboratory, Zanzibar ,Tanzania said "You are doing good job to assists in research. God bless you.".
    Rating: Very Good
View Other Reviews »

Paper Information

Format:MS WORD
Chapter:1-5
Pages:35
Attribute:EXPERIMENT
Price:₦3,000
Get The Complete Project »

Best Selling Projects

Our Archives

Featured Posts